This datasheet contains final specifications. Fairchild. Semiconductor reserves the right to make changes at any time without notice in order to improve design. IRFS Specifications. alldatasheet, free, Datasheets, databook. IRFS data sheet, Manual, IRFS parts, chips, ic, Electronic Components. application. IRFS from Samsung Semiconductor Division. Find the PDF Datasheet, Specifications and Distributor Information.

Author: Mataur Kasho
Country: Togo
Language: English (Spanish)
Genre: Automotive
Published (Last): 7 January 2006
Pages: 171
PDF File Size: 5.90 Mb
ePub File Size: 11.65 Mb
ISBN: 422-3-17743-934-1
Downloads: 38578
Price: Free* [*Free Regsitration Required]
Uploader: Volmaran

I read somewhere about re-magnetizing the exciter with 12V, So i did.


After check datasheet of 2n, frequency is very low Transition Frequency ft: No, create an account now. The four basic DC-DC converters considered for analysis are the following: Jun 26, Irds640 really don’t think the AVR is regulating properly though, at 1kw the output voltage is dropping to a bit below vac and 2kw vac.

So I opted to replace them. Now I am getting like 2VAC at the outlets. Yes, my password is: Jan 30, 13 4.

IRFS640 – 200V N-Channel B-FET / Substitute of IRF640 & IRF640A 200V N-Channel MOSFET

I just can’t get the darn AVR thing right. When i got it, it was not producing power. Mar 4, Jul 18, Aug 17, 5 1.


And a 2n to replace 2n I’ve redrawn the schematics to irfss640 understand the circuit topology. May 1, 2 0. The PWM signal is generated by permanently connecting the Mosfet gate to the Vcc bus through that current limiting resistor and by the BJT, which is shunting to ground the Mosfet gate whenever the feedback voltage is greater than the preset threshold VR1.

Itfs640 17, I do some checking, and the Darlington I put in was sorted, ratasheet was one of the BJt’s again. Discussion in ‘ The Projects Forum ‘ started by dmechanicJan 14, In this case what IS the role of C2 R2 between bjt base and negative brush?

I jumped across the brushes and voila power, only it was volts Mar 27, After they were in, still nothing.

Mar 3, The only components I hadn’t replaced were the resistors at R and R5. Load Output Sample Rotor 0 kw vac So i KNOW that the coils and exciter are working.

What do you mean by inductor? Oct 24, Generator Automatic Voltage Regulator Posted by debe in forum: I Jumped the 12v across the exciter brushes and got 30vac momentarily at the power outlets.

It is actually the Mosfet “load”. The motor also appears to be struggling at 2kw even though It is a 6. Jul 19, Quote of the day.


IRFS640 PDF Datasheet浏览和下载

Jun 25, Rotor winding or feed winding? Automatic Voltage Regulator Posted by preye in forum: You May Also Like: Mostly because i forgot to order them.

Do you already have an account? Stupid question but i want to understand. I will, however, check the sampling voltage and rotor slip ring voltage against load next. You might put a reverse biased diode across the BJT base-emitter datasneet to avoid any collector-base datawheet greater than 10V D2 zenner then any regular small signal BJT could do the job you don’t need a V rated one.

Automatic Voltage Regulator Posted by Dumken in forum: Can i use mosfet irf to replace irfs So I bough virtually all the components to rebuild the entire board based on the schematic on pg1 as well as the some recommendations for a different Varistor at Dataheet.

While they do appear to be okay on the outside, with a minimal mark on one of them, they all test OK and are within range for their values.